Les Spécialistes des Métiers de l’Eau et du Paysage 105 WIRELESS MINI-CLIK: RAIN SENSOR ITEM DESCRIPTION CATALOG NO. 1 Wireless Mini-Clik Transmitter Only WM-CLIK-TR 2 Wireless Mini-Clik Cap with Spindle Assembly 10023600SP 3 Wireless Mini-Clik Quick Shutoff Cover 10023900SP 4 Mounting Bracket 439700 5 Sensor Gutter Mount SGM 6 Receiver Assembly WR-CLIK-R 7 Receiver Rubber Cover 231300SP 8 Vandal-Resistant Wireless Sensor Guard for Flat Surfaces or Pole Mounting WS-GUARD 9 Vandal-Resistant Wireless Receiver Guard for Pedestal Mounting WR-GUARD SENSORS B C D B C 6 ⑧ ⑨ 1/8 1/4 1/2 3/4 1/8 1/4 1/2 3/4 ⑤ ④ OF THE USE OF CERTAIN HAZARDOUS SUBSTANCES IN ELECTRICAL AND ELECTRONIC EQUIPMENT (RoHS) NO DESIGN CHANGE ON PROPRIETARY TOOLING AND NO PURCHASED PART 2. SUBSTITUTION SHALL BE ALLOWED WITHOUT PRIOR EXPLICIT WRITTEN APPROVAL BY ENGINEERING, TOOLING, AND MANUFACTURING PN 231500 (ASSY, PCB, TRANSMITTER) MUST BE COATED WITH 3. SCHENECTADY ISONEL 642 PRIOR TO POTTING PN 10023300 (CHASSIS) SHALL BE POTTED UNTIL FILL LINE SPECIFIED. TOP OF 4. RED LED SHALL REMAIN VISIBLE. PN 10023400 (ASSY, BASE) SHALL BE FULLY SNAP FIT INTO CHASSIS IN 5. LOCATIONS SPECIFIED PN 10024000 (DOWEL PIN, .063" x 1" LG) SHALL BE PRESS-FIT UNTIL FLUSH OR 6. BELOW SURFACE AS SHOWN PN 605505 (INTERFACE, ARM) SHALL H VE MEK APPLIED TO INNER SURFACE 7. PRIOR TO INSTALLATION PN 605505 (INTERFACE ARM) SHALL BE SNAP FIT TO CHASSIS IN LOCATIONS 8. SPECIFIED 1 R&D INITIAL RELEASE CM 07/28/20 REV ECO REVISION DESCRIPTION DRFT DATE THIRD ANGLE PROJ. N/A DO NOT S ALL DIMENSIO SURFACE FINISH: UNLESS OTHE ① 1 2 3 4 7 5 10 11 8 6 9 ITEM NO. PART NUMBER 1 231800 2 10023600 3 10023900 4 10023300 5 789000 6 607600 7 605505 8 439700 9 206498 10 137200 11 10023400 12 10024000 13 231500 14 503900 15 223100 THIS DRAWIN DISCLOSURE O NO PATENT L 018 ② ③ 3 4 5 APPROVAL BY ENGINEERING, TOOLING, AND MANUFACTURING PN 231500 (ASSY, PCB, TRANSMITTER) MUST BE COATED WITH SCHENECTADY ISONEL 642 PRIOR TO POTTING PN 10023300 (CHASSIS) SHALL BE POTTED UNTIL FILL LINE SPECIFIED. TOP OF RED LED SHALL REMAIN VISIBLE. PN 10023400 (ASSY, BASE) SHALL BE FULLY SNAP FIT INTO CHASSIS IN LOCATIONS SPECIFIED PN 10024000 (DOWEL PIN, .063" x 1" LG) SHALL BE PRESS-FIT UNTIL FLUSH OR BELOW SURFACE AS SHOWN PN 605505 (INTERFACE, ARM) SHALL HAVE MEK APPLIED TO INNER SURFACE PRIOR TO INSTALLATION PN 605505 (INTERFACE ARM) SHALL BE SNAP FIT TO CHASSIS IN LOCATIONS SPECIFIED 1 R&D INITIAL RELEASE CM 07/28/20 REV ECO REVISION DESCRIPTION DRFT DATE DR BY THIRD ANGLE PROJ. .XX = ±.01 .XXX = ±.005 .XXXX = ±.0005 ±1° ANGLES: N/A DO NOT SCALE DRAWING ALL DIMENSIONS ARE IN INCHES SURFACE FINISH: UNLESS OTHERWISE SPECIFIED: PR DA SC Ma Sp Co RE DA DIMENSIONAL TOLERANCES: ⑥ ⑦
RkJQdWJsaXNoZXIy NzIyMzg3